Send Email
Send SMS
Search
Gubbi Enterprises
Gubbi Enterprises


Cement Testing Equipment

We are manufacturing & supplying Cement testing equipment which includes, Flow table, Vicat needle apparatus, gauging trowel, Le- Chatlier Mould, Mortar Mixer, Tensile testing machine, vibrating machine, Lab cement autoclave, cement sampler, Marsh cone, shrikange bar mould, flexural testing machine, Length compactor, Blain's air permeability, Standard spatula.

Vicat Needle Apparatus

REQUEST CALLBACK

Vicat Needle Apparatus
Approx. Rs 1,900 / No(s)
Get Best Quote

Our Vicat needle apparatus is used for determining the normal consistency and setting times of cement and 'A' Class limes. Our apparatus consists of a metallic frame bearing a freely movable rod with:

· Cap at top

· Vicat mould

· Split type and glass base plate

· Set of needles one each initial needle and final needle

· Consistency plunger.


Apart from this we also offer Vicat needle apparatus with dashpot which is fitted with dash pos which facilitates gentle lowering of needles. These are offered with accessories like mild steel base plate which is 5 inches x 5 inches. In addition to this, we offer fulcrum mould, brass, 70mm 1.0 base dia x 60mm i.d. top dia, and 40mm height.

 

 

Yes! I am interested

Flexural Testing Machine

REQUEST CALLBACK

Flexural Testing Machine
Approx. Rs 32,500 / No(s)
Get Best Quote

The machine consists of a hand frame. The lower platen has two rollers the distance between which is adjustable For 150 mm x 150 mm x 700 mm beam, the centre distance between rollers is 600 mm, while it is 400 mm for beams of size 100mm x 100mm x500mm. The upper platen has also a pair of rollers whose distance is adjustable. It is 200mm centre to centre, for 150mm x 150mm x 700mm size beam and 133 mm for 100 mm x 100 mm x 500 mm size beam. A pressure gauge to indicate load is fixed on the load frame. A small pumping unit is attached to the load frame. Total capacity of the machine is 100 KN and a 150mm dia pressure gauge 0-100 KN x 1 KN is fitted on the machine Since this is a hand operated light weight machine, its is useful for field laboratory also.

 

Hand operated, 100 tone

 

 

Yes! I am interested

Length Compactor

REQUEST CALLBACK

Length Compactor
Approx. Rs 11,900 / No(s)
Get Best Quote

IS 1199-1959, IS 4031 1968 BS 1881, ASTM C 151, C490

It is used to measure the dying shrinkage of concrete autoclave expansion of Portland cement and potential expansive reactivity of cement aggregate combinations in mortar bars during storage, on self drying.

The instrument consists of a channeled base over which two vertical pillars are fixed. An adjustable cross plate is at the top. A dial gauge, reading to .002mm x 12mm. Can be located upon a 6.5mm. dia ball or other reference point cemented in the specimen. On the base there is similar recessed seating in which can be placed a second ball or reference point in the specimen.

Complete with a stainless steel standardization bar with insulated grip and with 6.5mm dia. Balls mounted in the ends. The unit can be supplied with an Electronic Dial Gauge at extra cost if indicated at the time of placing the order.

 

Yes! I am interested

Cement Sampler

REQUEST CALLBACK

Cement Sampler
Approx. Rs 1,950 / No(s)
Get Best Quote

This is a brass tube approximately 53 cm long and 2.8 cm I.D. with a wooden handle. Total length approximately 73cm. The tube has the sharp angular edge which conveniently pierces cement bags. An air hole of approximately 3mm dia is drilled on the tube near handle. Total sample collected at one time is 300 cm approximately.

Yes! I am interested

Gauging Trowel

REQUEST CALLBACK

Gauging Trowel
Approx. Rs 345 / No(s)
Get Best Quote

 

BS 12, IS 4031 Weight approximately 210 gms.. Best quality with hard wood handle blade length 200mm. ASTM: C 190, IS: 4031 100 to 150mm long steel blade with straight edges.

Yes! I am interested

Blaine S Air Permeability Apparatus

REQUEST CALLBACK

Blaine S Air Permeability Apparatus
Approx. Rs 2,200 / No(s)
Get Best Quote

The apparatus is used for determining the fineness of cement in terms of specific surface expressed as total surface area in square centimeters per gram of cement. This is a variable flow type air permeameter.

 

Salient Features

  • Specifications : The apparatus consists one each of permeability cell 12.5mm I.D., Manometer 'U' type mounted on stand with a built in stop cock, Perforated disc, Plunger Rubber stopper, Rubber tube 30cm long. Packet of 12 filter paper discs and a bottle of 100cc dibutyiphthalate liquid.
    Spares and Accessories: Punch to cut filter paper discs. Non-perforated disc. Suction
Yes! I am interested

Flow Table for Building Limes

REQUEST CALLBACK

Flow Table for Building Limes
Approx. Rs 12,500 / No(s)
Get Best Quote

This is used for determining the workability of building limes.

 

Specifications:

The flow table consists of a 30cm. dia ground and polished steel plate with three inscribed annular circles. 7, 11 and 19cm. dia. The table top is arranged for a free fall of 12.5mm by a cam action. Supplied complete with one brass conical mould, 65mm I.D. at base and 40mm I.D. at top, height of the mould 90mm

Yes! I am interested

Flow Table For Cement Concrete

REQUEST CALLBACK

Flow Table For Cement Concrete
Approx. Rs 23,500 / No(s)
Get Best Quote

FLOW TABLE for Cement Concrete - 30 MS top HAND OPERATED

IS 1199-1959, ASTM C-124, AASHTO-T-120. It is used for determining the flow of cement concrete. SPECIFICATION : Consists of a steel table top 76.2cm 30 inch. Dia Finely machined. The integral cast ribs are designed for support and strength. The stand is fabricated out of cast iron and is of study construction. Holes for mounting in foundations are drilled in the base plate
Yes! I am interested

Flow Table For Cement Concrete- Motorised 30 MS

REQUEST CALLBACK

Flow Table For Cement Concrete- Motorised 30 MS
Approx. Rs 34,500 / No(s)
Get Best Quote

FLOW TABLE for Cement Concrete-motorised 30 MS .

IS 1199, ASTM C-124, AASHTO-T-120 SPECIFICATION : Consists of a steel table top 76.2cm 30 inch. Dia Finely machined. The integral cast ribs are designed for support and strength. The stand is fabricated out of cast iron and is of study construction. Holes for mounting in foundations are drilled in the base plate. The ground and hardened steel cam is designed to fit and drop the table by 12.5mm. The hand wheel makes it simple to operate the table.
Yes! I am interested

Standard Spatula

REQUEST CALLBACK

Standard Spatula
Approx. Rs 980 / No(s)
Get Best Quote

IS 4031, 269, BS 12 This is for use while casting a cement briquette. SPECIFICATION : The standard spatula consists of a steel blade, of a special shape. A wooden handle is fixed to the stem of blade. The weight does not exceed 340 gms
Yes! I am interested

Lab Cement Autoclave

REQUEST CALLBACK

Lab Cement Autoclave
Approx. Rs 42,500 / No(s)
Get Best Quote

IS 4031-1968, IS 1624-1960 & ASTM C 151, C 141

The autoclave is suitable for conducting accelerated soundness tests on cements or the autoclave expansion test requiring constant steam pressure with the correspondent constant pressure. It consists of a stainless steel cylinder with a welded heat insulated metal housing attractively finished. The attached control unit encloses a sensitive pressure regulator and pressure gauge. Power switches and pilot lights for controlling the electric heating units. Inside chamber dimensions 10.5 cm diameter x 40.5cm height suitable for operation on 230 V, 50 Hz Single Phase A. C. supply. Supplied complete with test bar holder, special rack to hold specimens above water level in the autoclave and in a vertical position to expose them in the same manner. A Digital PID Controller is fitted for controlling the desired temperature.




Yes! I am interested

Marsh Cone

REQUEST CALLBACK

Marsh Cone
Approx. Rs 6,200 / No(s)
Get Best Quote

ASTM D 2419, AASHTO T 176


This cone is used to find out viscosity of bentonite slurry and similar material. The marsh cone is 6 inch in diameter at the top and 12 inch long, and tapers to join a tube 2 inch long and 3/16 inch inside dia. The capacity of the funnel is 1500cc. Time in seconds required to flow out 1000cc of slurry from cone is measured as funnel viscosity of the material.

Yes! I am interested

Le-Chatlier Mould

REQUEST CALLBACK

Le-Chatlier Mould
Approx. Rs 1,850 / No(s)
Get Best Quote

We supply technically advanced range of le- chatelier mould which is extensively used for soundness test of the cement. In this apparatus it includes a small split cylinder forming a mould of 30mm internal dia and which is 30 mm high. Two parallel indicating arms with pointed ends are fixed on either side of the fixed cylinder. The mould is offered with two glass plates and lead weights. Moreover, a set of six moulds is supplied in the cardboard box. Our product is fabricated in compliance with IS: 5514 standard and can be delivered on time.

Yes! I am interested

Vibrating Machine

REQUEST CALLBACK

Vibrating Machine
Approx. Rs 20,900 / No(s)
Get Best Quote

The vibrating machines which we offer are also called mould vibrator or mortar cube vibrators. Our vibration machines are used for the preparation of mortar cubes for the determination of compression strength of ordinary and rapid hardening:

· Portland cement

· Low heat Portland cement

· Portland blast furnace cement

· High alumina cements


Salient Features

· The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base.

· The complete frame assembly consists of a vice to hold a 7.06 cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould.

· This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame.

· A balance weight is an integral bottom part of the frame.

· The centre of gravity of the assembly is brought to the centre of the eccentric shaft or within a distance of 25mm mould.

· The frequency of vibration is 12000 400 vibration per minute.

· Supplied complete with on 7.06cm cube mould with loose base plate, a time switch 0-5mins x 1min and certificate of vibration from a standard laboratory.

· Spares offered: Set of springs, belt and belt guard

Yes! I am interested

Shrinkage Bar Mould 25x25x250mm Single Gang

REQUEST CALLBACK

Shrinkage Bar Mould 25x25x250mm Single Gang
Approx. Rs 780 / No(s)
Get Best Quote

Shrinkage Bar Mould 25x25x250mm Single Gang

The mould is used for casting specimens of cement & aggregate combinations for measuring the potential expansive alkali reactivity.

Specification : The mould, which has 25 mm x 25 mm x 250 mm, effective gauge length is made of mild steel and has accurately machined faces. The parts of the moulds are tight fitting and firmly held together when assembled. Supplied complete with base plate and four stainless steel smooth reference pins.
Yes! I am interested

Mortar Mixer

REQUEST CALLBACK

Mortar Mixer
Approx. Rs 35,500 / No(s)
Get Best Quote

IS 4031, 1727 & BS 3892

It is used for mixing cement pastes, mortars and pozzolana.

Specification : The apparatus consists of an epicyclical type stainless steel paddle imparting both planetary and revolving motion, by means of gears. It has two speeds of 140 + 5 R.P.M. And 285 +10 R.P.M. With planetary motions of approximately 62 r.p.m, +5 R.P.M. And 125 R.P.M. +/- 10 R.P.M. Respectively. The stand of the mixer has arrangement to raise or lower the bowl. Complete with stainless steel bowl of about six liters capacity. Suitable for operation on 230 V, 50 cycles, Single Phase A.C, Supply.


Yes! I am interested

Shrinkage Bar Mould 25x25x250mm Two Gang

REQUEST CALLBACK

Shrinkage Bar Mould 25x25x250mm Two Gang
Approx. Rs 1,450 / No(s)
Get Best Quote

Shrinkage Bar Mould 25x25x250mm Two Gang

The mould is used for casting specimens of cement & aggregate combinations for measuring the potential expansive alkali reactivity.

Specification : The mould, which has 25 mm x 25 mm x 250 mm, effective gauge length is made of mild steel and has accurately machined faces. The parts of the moulds are tight fitting and firmly held together when assembled. Supplied complete with Two compartments assembled on angle base plate.
Yes! I am interested

Shrinkage Bar Mould 25x25x250mm Three Gang

REQUEST CALLBACK

Shrinkage Bar Mould 25x25x250mm Three Gang
Approx. Rs 2,100 / No(s)
Get Best Quote

Shrinkage Bar Mould 25x25x250mm Three Gang

The mould is used for casting specimens of cement & aggregate combinations for measuring the potential expansive alkali reactivity.

Specification : The mould, which has 25 mm x 25 mm x 250 mm, effective gauge length is made of mild steel and has accurately machined faces. The parts of the moulds are tight fitting and firmly held together when assembled. Supplied complete with base plate and four stainless steel smooth reference pins with Three compartments.

 

Yes! I am interested

Shrinkage Bar Mould 25x25x250mm Four Gang

REQUEST CALLBACK

Shrinkage Bar Mould 25x25x250mm Four Gang
Approx. Rs 2,850 / No(s)
Get Best Quote

Shrinkage Bar Mould 25x25x250mm Four Gang

The mould is used for casting specimens of cement & aggregate combinations for measuring the potential expansive alkali reactivity.

Specification : The mould, which has 25 mm x 25 mm x 250 mm, effective gauge length is made of mild steel and has accurately machined faces. The parts of the moulds are tight fitting and firmly held together when assembled. Supplied complete with base plate and four stainless steel smooth reference pins but having Four Compartments.
Yes! I am interested

Tensile Testing Machine Up To 1000 Kg

REQUEST CALLBACK

Tensile Testing Machine Up To 1000 Kg
Approx. Rs 1.01 Lakh / No(s)
Get Best Quote

Floor mounted, vertical type, two column construction specially manufactured for various applications. TENSILE TESTING MACHINES are designed for determining the Tensile Strength and Elongation of a host of materials like ferrous and non ferrous materials, cables & conductors, Plastic, PVC, Rubber specimens, paper, plywood etc. Our TENSILE TESTING MACHINES are also capable for conducting compression, Cross breaking and Shear tests thus making them more versatile with a few additional attachments
Yes! I am interested

Tensile Testing Machine up to 250 kg

REQUEST CALLBACK

Tensile Testing Machine up to 250 kg
Approx. Rs 85,000 / No(s)
Get Best Quote

Floor mounted, vertical type, two column construction specially manufactured for various applications. TENSILE TESTING MACHINES are designed for determining the Tensile Strength and Elongation of a host of materials like ferrous and non ferrous materials, cables & conductors, Plastic, PVC, Rubber specimens, paper, plywood etc. Our TENSILE TESTING MACHINES are also capable for conducting compression, Cross breaking and Shear tests thus making them more versatile with a few additional attachments.
Yes! I am interested

Tensile Testing Machine Up To 500 Kg

REQUEST CALLBACK

Tensile Testing Machine Up To 500 Kg
Approx. Rs 92,500 / No(s)
Get Best Quote

Floor mounted, vertical type, two column construction specially manufactured for various applications. TENSILE TESTING MACHINES are designed for determining the Tensile Strength and Elongation of a host of materials like ferrous and non ferrous materials, cables & conductors, Plastic, PVC, Rubber specimens, paper, plywood etc. Our TENSILE TESTING MACHINES are also capable for conducting compression, Cross breaking and Shear tests thus making them more versatile with a few additional attachments
Yes! I am interested

Tensile Testing Machine Up To 100 Kg

REQUEST CALLBACK

Tensile Testing Machine Up To 100 Kg
Approx. Rs 79,500 / No(s)
Get Best Quote

Tensile Testing Machine up to 100 kg

Floor mounted, vertical type, two column construction specially manufactured for various applications. TENSILE TESTING MACHINES are designed for determining the Tensile Strength and Elongation of a host of materials like ferrous and non ferrous materials, cables & conductors, Plastic, PVC, Rubber specimens, paper, plywood etc. Our TENSILE TESTING MACHINES are also capable for conducting compression, Cross breaking and Shear tests thus making them more versatile with a few additional attachments. TENSILE TESTING MACHINES are available in various capacities depending upon the requirements right from 5 kgf to 10 Tonnes ensuring ± 1% accuracy in test results. We assure high accuracy, sensitivity, reliability, consistency, repeatability and excellent workmanship. TENSILE TESTING MACHINES are backed up by prompt and effective after service by a team of factory trained technicians. Our machines are available in KGF/ kN/N as per your specific requirements. TENSILE TESTING MACHINES are also available with State of Art Electronic Microprocessor based Digital Indicator systems with PC and Printer.
Yes! I am interested

 
X


Call Us:  +91-8079456421
Gubbi Enterprises
Sidheshwar Jamma (Proprietor)
18/26, Dev Prayag CHS, Bhakti Mandir Road Hari Niwas Circle, Thane West, Opposite Thanawala Garrage, Kalwa,
Thane - 400605, Maharashtra, India
Contact via E-mail
Contact via SMS



Home  |   About Us   |  Products & Services  |  Site Map  |   Contact Us   |   Mobile Site

© Gubbi Enterprises. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited

Gubbi Enterprises